The Squeeze Cast Small Stream Fly Fishing
When heading out for an evenings go at a local small water Trout stream, you might consider the following tips.I suggest you use a Double Taper fly line versus a Weight Forward line. This fills up the spool a little quicker with less weight and is better suited for the many Roll Casts an evenings fly fishing on small streams usually requires. Also, use either an 8# or 12# backing line if you can find it. Not a real big deal but keeping the weight down on small stream outfits is useful.Small stream fly rods do not normally require a very long casting stroke. A key to accurate casting with these short rods (5' to 7') is to execute both your back cast and forecast with a very short casting stroke, the shorter the better. Smooth acceleration to an immediate stop, almost like punching a wall, then hold the rod stopped until the cast is almost completely laid out....then drop your elbow (without extending your arm or body) to present the fly.Another tip.........to increase speed and accuracy very quickly.....AS YOU ARE EXECUTING YOUR BACK CAST......OPEN YOUR 3 LOWER FINGERS......control the rod with your thumb and fore finger. (keep the back of the rod handle up against the fleshy part of your hand) HOLD THE ROD WITH THESE TWO FINGERS tungsten worm weights THRU THE BACK CAST. .........Just as you are finishing your fore cast......SHARPLY SQUEEZE.....THE 3 FINGERS TOGETHER AGAINST THE LOWER PART OF THE ROD HANDLE and your thumb against the top of the rod handle...... THIS GIVES A FINAL, RAPID ACCELERATION TO THE STOPPING of the rod.....SPEEDING UP THE LINE AND IMPROVING ACCURACY....TAKES A LITTLE PRACTICE BUT REALLY IMPROVES A CAST IN A TIGHT SITUATION.Give it a try and let me know how it works for you...I call this "The Squeeze Cast"....tricky name I thought......Best Joe @ Castitagain.
by bobeileen
| 2021-10-15 17:25

MILLING INSERTS,PARTING AND GROOVING INSERTS,,Estoolcarbide.com is professional tungsten carbide cutting tools manufacturer.
by bobeileen
以前の記事
2026年 02月
2026年 01月
2025年 12月
2025年 11月
2025年 10月
2025年 09月
2025年 08月
2025年 07月
2025年 06月
2025年 05月
2025年 04月
2025年 03月
2025年 02月
2025年 01月
2024年 12月
2024年 11月
2024年 10月
2024年 09月
2024年 08月
2024年 07月
2024年 06月
2024年 05月
2024年 04月
2024年 03月
2024年 02月
2024年 01月
2023年 12月
2023年 11月
2023年 10月
2023年 09月
2023年 08月
2023年 07月
2023年 06月
2023年 05月
2023年 04月
2023年 03月
2023年 02月
2021年 10月
2021年 09月
2021年 08月
2021年 07月
2021年 06月
2021年 05月
2021年 04月
2021年 03月
2026年 01月
2025年 12月
2025年 11月
2025年 10月
2025年 09月
2025年 08月
2025年 07月
2025年 06月
2025年 05月
2025年 04月
2025年 03月
2025年 02月
2025年 01月
2024年 12月
2024年 11月
2024年 10月
2024年 09月
2024年 08月
2024年 07月
2024年 06月
2024年 05月
2024年 04月
2024年 03月
2024年 02月
2024年 01月
2023年 12月
2023年 11月
2023年 10月
2023年 09月
2023年 08月
2023年 07月
2023年 06月
2023年 05月
2023年 04月
2023年 03月
2023年 02月
2021年 10月
2021年 09月
2021年 08月
2021年 07月
2021年 06月
2021年 05月
2021年 04月
2021年 03月
フォロー中のブログ
メモ帳
最新のトラックバック
ライフログ
検索
ブログパーツ
最新の記事
| CNC Tool Setup.. |
| at 2026-02-10 16:09 |
| What Are the C.. |
| at 2026-02-03 10:58 |
| How Do Carbide.. |
| at 2026-01-29 12:20 |
| What Makes CNM.. |
| at 2026-01-21 11:52 |
| Maximizing Too.. |
| at 2026-01-14 15:56 |
